Buy Now Pay Later • Free Shipping • Easy Returns

Regulatory Information (EN)

United States

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The SAR limit set by the FCC and ISED are 1.6W/kg. For wearable operation, this device has been tested and meets the FCC and ISED RF exposure guidelines at a minimum separation distance of 5 mm from the body. RF exposure compliance with any third parties accessory was not tested and certified, any third parties accessory is not recommended, a minimum separation of 5mm must be kept when in wearable operation.

Canada

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

European Union

COMPLIANCE WITH 2014/53/EU RADIO EQUIPMENT DIRECTIVE (RED)
Milo complies with the requirements of Article 10(2) as they can operate in at least one Member State as examined. In accordance with Article 10(10), in cases of restrictions on putting into service, information available on the packaging shall allow the identification of the Member States or the geographical area within a Member State where restrictions on putting into service or requirements for authorization of use exist. Specific Absorption Rate (SAR) information: The EU SAR limit For Body Worn is 2.0W/kg and For Limb is 4.0 W/kg. This device should keep 5mm separation distance for wearable operation and 10mm separation distance for push to talk operation. The Maximum Body SAR is 0.290W/kg; The Maximum Limb SAR is 0.290W/Kg. Milo meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. In accordance with Article 10.8(a) of the RED, the following table provides information of the frequency bands used and the maximum radio frequency transmit power of Milo Handheld transceiver for sale in the EU.
Function Frequency Max. Transmit power
Bluetooth 2402-2480 MHz 9 dBm (EIRP)
Bluetooth LE 2402-2480 MHz 4 dBm (EIRP)
WiFi 2.4G 2412-2472 MHz 19 dBm (EIRP)
WiFi 5G 5180-5320 MHz 18 dBm (EIRP)
WIFI 5G 5500 -5700 MHz 17 dBm (EIRP)
Milo 2.4G 2400 MHz-2483.5 MHz 17 dBm (EIRP)
Milo Band K 863 -865 MHz 13.7 dBm  (ERP)
Milo Band L 865 -868 MHz 13 dBm (ERP)
Milo Band P 869.4-869.65 MHz 22 dBm (ERP)

Informations réglementaires (FR)

États-Unis

DÉCLARATION DE CONFORMITÉ FCC ET IC

Cet appareil a été testé et déclaré en conformité avec la section 15 des directives FCC et aux exigences de l’organisme canadien Innovation, Sciences et Développement économique (ISDE) . Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer dʼinterférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y compris des interférences susceptibles dʼoccasionner un fonctionnement non souhaité.

Vous trouverez une copie de chaque déclaration de conformité à l’adresse internet suivante: www.okmilo.com/support.

Le seuil de débit d’absorption spécifique (DAS) défini par les directives FCC et par l’ISDE est de 1,6 W/kg. Cet appareil a été testé pour être porté à une distance minimale de 5 mm du corps conformément aux directives FCC et aux exigences de l’ISDE. Aucun test n’a été effectué ni aucun certificat délivré quant à la comptabilité en matière d’exposition aux radiofréquences (RF) avec des appareils tiers. Par conséquent, l’utilisation d’appareils tiers n’est pas recommandée. Une distance minimale de 5 mm doit être respectée lorsque l’on porte l’appareil.

Canada

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

  1. L’appareil ne doit pas produire de brouillage;
  2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Union européenne

CONFORMITÉ AVEC LA DIRECTIVE EUROPÉENNE 2014/53/UE RELATIVE AUX ÉQUIPEMENTS RADIOÉLECTRIQUES (RED)
Milo respecte les conditions de l’art. 10, al. 2, car l’appareil peut être utilisé dans au moins un pays membre. Conformément à l’art. 10, al. 10, les informations figurant sur l’emballage permettent d’identifier les États membres ou la zone géographique à l’intérieur d’un État membre dans lesquels existent les restrictions à la mise en service ou les exigences concernant l’autorisation d’utilisation de l’appareil. Dans tous les États membres de l’UE, l’utilisation à 5150-5250 MHz n’est autorisée que dans les espaces clos. Informations relatives au DAS : le seuil DAS autorisé par l’UE lorsque l’appareil est porté sur le corps est de 2,0 W/kg et de 4,0 W/kg sur les membres. Une distance minimale de 5 mm doit être respectée lorsque l’on porte l’appareil et de 10 mm lorsque l’on utilise la fonction « Presser pour parler ». Le seuil maximal DAS pour le corps et pour les membres est de 0,290 W/kg. Milo respecte les exigences gouvernementales en matière d’exposition aux ondes radio. Les règles se basent sur des standards développés par des organisations scientifiques indépendantes ayant évalué périodiquement et minutieusement les études scientifiques. Les standards incluent une marge de sécurité considérable, mise en place pour assurer la protection de toute personne, indépendamment de l’âge ou de l’état de santé. Conformément à l’art. 10, al 8, let. de la RED, le tableau suivant fournit des informations relatives aux bandes de fréquence utilisées et à la puissance d’émission des RF de l’émetteur-récepteur portatif Milo en vente au sein de l’UE.
Fonction Fréquence Puissance d’émission max.
Bluetooth 2402-2480 MHz 9 dBm (EIRP)
Bluetooth LE 2402-2480 MHz 4 dBm (EIRP)
WiFi 2.4G 2412-2472 MHz 19 dBm (EIRP)
WiFi 5G 5180-5320 MHz 18 dBm (EIRP)
WIFI 5G 5500 -5700 MHz 17 dBm (EIRP)
Milo 2.4G 2400 MHz-2483.5 MHz 17 dBm (EIRP)
Milo Band K 863 -865 MHz 13.7 dBm  (ERP)
Milo Band L 865 -868 MHz 13 dBm (ERP)
Milo Band P 869.4-869.65 MHz 22 dBm (ERP)

Australia and New Zealand

COMPLIANCE WITH RCM AND RSM

Loose Cannon Systems, Inc, declares that the radio frequency bands 863Mhz-869.65Mhz will be disabled in all products supplied to the Australian and New Zealand market. The end-user will not be able to activate or use these unauthorized bands.
The following table provides information of the radio frequency bands used.

Function Frequency
Bluetooth 2402-2480 MHz
Bluetooth LE 2402-2480 MHz
WiFi 2.4G 2412-2472 MHz
WiFi 5G 5180-5320 MHz
WIFI 5G 5500 -5700 MHz
Milo 2.4G 2400 MHz-2483.5 MHz
USD
USD-currency-flag
CAD
CAD-currency-flag
USD
USD-currency-flag
CAD
CAD-currency-flag